Tuesday, June 5, 2012

Titan update

So the I've finished the 4 legs, gotten them cleaned up and prepped to remold the tips of the legs after putting some solid pins in there.  I found the leg tips were pretty flimsy, and sparse, so I cut them back far enough to pin in the pins.  Most of the spiked fins were also pretty deformed or flimsy, so I removed most of them, I'm thinking I may just remove them all and either put individual bits on all the legs, or cast the fins by themselves.

Four legs, pinned and ready for Green stuff
While resin was curing and in between leg cleanup, I moved on to the torso piece, and upper legs.  I had originally decided that I was going to use a ball type joint on the upper leg to connect to the torso as well.  I expected to cast and mold that as well, but as I was looking a little closer at the Forgeworld Eldar titans I noticed they usually used a flat connection.  So I picked up some 7/16" Evergreen tubing and I'm just going to connect using the tubes cut to size.  The torso had holes pre-drilled to fit the ball joints, so I just expanded them slightly so the tubing will fit.

Torso with a small mistake
I had used a series of PVC pike connectors to build the torso, it is a larger 1" piece, with a smaller connector fit inside, and half of a third smaller connector within the second one.  You can see the second connector with the leg holes, and you can see the third connector through the holes, and the small stop piece at the bottom.  This gave a nice little tapering effect towards the bottom, I just needed to expand the top a bit so I could make it resemble the Kabalite Warrior torso.  So as I was cleaning up, I found an old Tylenol bottle that was the right size, I had to expand the opening, and then slipped it on the top of the PVC connector.  This gave me a nice thickness for the torso, as well as a flat top with a slight indent to attach the head at a later point.  A short set of 1/2" tubing was added to either side of the medicine bottle to give the torso the width I wanted from shoulder to shoulder.  Now it was ready to be built up and get some definition going.

The first though was going to be heat and mold styrene around the frame until I got the shape I wanted, and then add detail to it until it was passable.  But since the gaming table doubles as the work area and is shared by my girlfriend and her daughter there are often lots of odds and ends kicking around for inspiration.  So the kid was working on trying to build items with the intent of going larger and larger to an eventual cosplay outfit.  One of the materials that she was using extensively was the sheets of flexible craft foam.  I was moving it out of the way and noticed how it flexed nicely, was of a decent thickness, and was easy to work with, so I asked to borrow a couple sheets.

Torso back with spinal plates
The torso plates were laid down from bottom up using the foam, because of the natural stepping nature of the frame I didn't have to do all the way to the top each time.  The one problem I had, is I got a little too anxious with foam and started forming the torso before I remembered that each band was supposed to taper up in the center where the hole was.  Still, the foam has worked great, it's given me a nice light frame that has been easy to work with.  The only real problem I've had is some shaping problems with edges, and stray bits and bobs can leave impressions in the foam.  After the torso was built, I cut away a section down the middle of the back and inserted the layered spinal plates, and guards on either side of that.  I think it came out quite nicely.

So the next step is going to be building the back fins, and deciding on what I want to do with the torso piece.  I had originally thought of casting the torso as well, but I realize that it may be too heavy to sit properly on the legs once everything is assembled.  So I've been throwing around a couple of ideas.  The other problem is how to prepare the foam for detail and paint.  I should be able to use a glue/water mixture to seal it like a foam terrain piece, or maybe even a sealer, but one of the things I've noticed when I get some resin spill over onto any newspaper is it soaks in and hardens almost like a fibreglass (which it should since it is basically the same product); so I may mix up some resin, and paint it onto the foam to harden it.  This may also be revisited for the flyer build as well.

On a seperate note, I may be moving soon, and I've heard there is a decent sized Apocalypse game being planned for the middle of this month, so I may try and hurry this to a standing frame with temporary weapons to try out.  As far as the MiniWarGaming Apocalypticon event, as I expected, they don't want to sent a precedent of having to manage house built rules, so if I get it built and am able to attend it will likely proxy as a Chaos Reaver.

2 comments:

  1. This is looking awesome, are you planning on attending apocalipticon this year?

    ReplyDelete
    Replies
    1. I hope to, but there are still a few things up in the air. I will probably have to proxy it as an existing titan, probably a Chaos Reaver. If I use a Vulcan Bolter, Laser Blaster, and Titan CCW it should work close to what I cooked up for rules.

      Delete